Your browser will redirect to your requested content shortly It's spring loaded and should fall when you empty the ice tray, but it could be stuck by ice or lack of lubrication. Whirlpool icemakers visit AppliancePartsPros.com. ones used for water supply to the kitchen faucet. Tony for Model Number WRF555SDZ02. The shut-off arm lifts up and down. The metal arm moves up and down. This will likely resolve the issue. If these troubleshooting steps do not resolve the issue, service is necessary to expertly diagnose and repair the product. They last less than two years. One of the issues that this loss of function can manifest is making too much ice. All the way up is the "off" position. Frost or ice can build up inside the ice maker or on the crucial parts like the feeler arm. Try and press the on/off switch and then lowering the arm manually to see if this helps. The next thing you need to check is the feeler arm (the arm that feels for ice and stops the icemaker when it feels some). is completed as designed. I know how disappointing it is when you are not getting ice. As ice is made, the arm is pushed up as ice is made and falls when the ice is dropped. The feeler arm, which functions like the float in a toilet, shuts off the ice maker when the ice tray is full. If your Whirlpool ice maker is not working, but your water dispenser is, then the control arm may be turned to the off position. Some feeler arms go up and down some go side-to-side. Uncategorized by . You can adjust by loosening the screws. That’s why it’s such a big inconvenience if your ice maker gets stuck or fails to produce enough ice. First, check the setting of your ice maker to be sure that you have it set at the proper level for making ice. In any case it should have a spring like action. The ice maker started freezing up and then when it gets so much ice back there on the walls, the ice maker quits working. When the ice maker gets stuck in the up position, there is no way to fix it without replacing the whole ice maker. Back Careers. A bent arm can cause these issue too. It was working fine, until I turned it off because it doesn't always shut off when the tray is full .
The valve may be faulty, causing too much water to go to the ice maker and could have overflowed it. A level might help. If so remove the ice from the ejector arm. If this happens, they may not function as designed. I had it serviced and the repair people completely replaced the ice maker. Next. If the water stops then it very well may be that the ice maker got stuck in a cycle just during the water command. It sounds like it may not be getting the proper amount of water. Greg for Model Number WRS571CIDM02. FYI, I’ve been in maintenance 37 years. After I realize the ice is running, every week or week and a half, I take it a part and clean it and work the arm that stops the ice maker when it full and sometimes it starts working and sometimes I have to do it all over and over again to make it work. Check that the ice is not jamming up on the ejector arm of the icemaker. Careers Link opens in a new tab. In my opinion, EVERY appliance sold should be designed to last a minimum of ten years. Use a plastic object to not damage the ice maker. I put the old arm back on and found that although I was still unable to move the arm down, I was able to click it up into another position.
The ice maker arm is another shut off switch for this model This happens all the time and then it isolates the overfilling to the ice maker. A Sulock from Phila, PA Answers: Ice Maker Arm is Stuck Another issue could be that the ice maker needs to be reset. So I removed the module and cleared out the ice and it started making ice. Turning the Ice Maker On/Off:-The On/Off switch, located on the left wall of the freezer door, can only be accessed when the ice storage bin has been removed.-To turn on the ice maker, flip the switch to the ON (up) position.-To manually turn off the ice maker… Hello Kim! For Whirlpool Icemaker Shut Off Arm (Part Number: AP6872223) ... My ice maker arm is stuck in the up position won't come down manually and it's not making any ice I unplug the frigerator for 10 minutes turn back on still not working then I shut off the ice maker for 5 minutes turned it back on still not working can you help. If your ice maker has gone into overdrive and won’t stop producing ice, it is usually because the bail arm (sometimes called feeler arm) is off balance. It worked for about 2 months and now back to the same issue. Part numbers can be serial number specific. chilled water half. We opened up the freezer and water wa we have had a whirlpool refrigerator for almost 2 years exactly. Have a very busy schedule and haven’t had a chance to exercise my warranty but plan to. Ice maker bin level arm stuck in the up position, i tried pulling it down with no avail so i unplugged the refrigerator for 2 minutes, plugged it back in and the arm still wont drop down. Push this arm down if it's stuck, and you should hear the sound of water flowing into the ice maker's reservoir. The ice maker is … The ice maker arm is another shut off switch for this model. December 3, 2020. Retest the unit operation. I will never buy a whirlpool product again. The "shut arm" on the ice maker of our bottom-mount freezer, Whirlpool Gold, single-door refrigerator sticks in the "off" position (up) after it ejects each load of ice. Back Whirlpool Appliance Repair. Don’t remove them, only loosen and adjust. The part was easy to replace. The other day I found that the ice maker was not ejecting ice. ), or to establish a professional-client relationship. The true test will be after the first batch freezes. The ice maker arm has fallen off many times and I simply replace it and it works fine and has for a long time, but this time it came off and when I replaced it, the arm will be in the down (on) position, 4-5 cubes will drop then the arm goes to the off position and stays there. As ice is made, the ice cubes will fill the ice storage bin, and the ice cubes will raise the shutoff arm to the OFF (arm up) position. Comments Off on whirlpool ice maker arm stuck halfway on whirlpool ice maker arm stuck halfway check the freezer door lower hinge area where the dispenser/ice maker wires exit the hinge and connect to the main cabinet. Press Center ... you count on your ice maker to work flawlessly. Its now come down to there isnt any more that the repair man can do so he said. If there were a better option on the market i would buy it. The ice maker is part number 4681JA1006K priced at $116.24. To turn off the icemaker, find the on/off toggle switch or slide switch on the side or front of the icemaker and turn it off. There is water to the unit. If the ice maker is overfilling and there is some flooding in the freezer, first turn the system off by raising the shut off arm. The ice maker seems to work well, but we must manually return the shut arm to the "open" position after each ice dump.